[DistroKit] [PATCH v2 2/7] v7a_noneon: use upstreamed devicetree the KSZ9477 EVB

[Oleksij Rempel <o.rempel@pengutronix.de>]

KSZ9477 EVB is already mainline and there are some naming differences.
So, drop downstream dts and use the mainline version.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 .../dts/at91-microchip-ksz9477-evb.dts        | 193 ------------------
 configs/platform-v7a_noneon/platformconfig    |   2 +-
 .../loader/entries/sama5d3-ksz9477-evb.conf   |   2 +-
 3 files changed, 2 insertions(+), 195 deletions(-)
 delete mode 100644 configs/platform-v7a_noneon/dts/at91-microchip-ksz9477-evb.dts

diff --git a/configs/platform-v7a_noneon/dts/at91-microchip-ksz9477-evb.dts b/configs/platform-v7a_noneon/dts/at91-microchip-ksz9477-evb.dts
deleted file mode 100644
index df77df5..0000000
--- a/configs/platform-v7a_noneon/dts/at91-microchip-ksz9477-evb.dts
+++ /dev/null
@@ -1,193 +0,0 @@
-/*
- * at91-sama5d3_xplained_ung8071.dts - Device Tree file for the EVB-KSZ9477 board
- *
- *  Copyright (C) 2014 Atmel,
- *		  2014 Nicolas Ferre <nicolas.ferre@atmel.com>
- *		  2018 Ahmad Fatoum <a.fatoum@pengutronix.de>
- *
- * Licensed under GPLv2 or later.
- */
-/dts-v1/;
-#include "sama5d36.dtsi"
-
-/ {
-	model = "EVB-KSZ9477";
-	compatible = "atmel,sama5d3-ksz9477-evb", "atmel,sama5d3", "atmel,sama5";
-
-	chosen {
-		stdout-path = &dbgu;
-	};
-
-	clocks {
-		slow_xtal {
-			clock-frequency = <32768>;
-		};
-
-		main_xtal {
-			clock-frequency = <12000000>;
-		};
-	};
-};
-
-&mmc0 {
-	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
-	status = "okay";
-	slot@0 {
-		reg = <0>;
-		bus-width = <8>;
-		/* cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>; */
-		broken-cd;
-	};
-};
-
-&spi0 {
-	cs-gpios = <&pioD 13 GPIO_ACTIVE_LOW>, <0>, <0>,
-	           <&pioD 16 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-0 = <&pinctrl_i2c0_pu>;
-	status = "okay";
-};
-
-&macb0 {
-	phy-mode = "rgmii";
-	status = "okay";
-
-	fixed-link {
-		speed = <1000>;
-		full-duplex;
-	};
-};
-
-&spi1 {
-	pinctrl-0 = <&pinctrl_spi_ksz>;
-	cs-gpios = <&pioC 25 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	switch@0 {
-		compatible = "microchip,ksz9477", "microchip,ksz9893";
-		reg = <0>;
-
-		/* Bus clock is 132 MHz. */
-		spi-max-frequency = <1000000>;
-		spi-cpha;
-		spi-cpol;
-		/* reset-gpios = <&pioC 31 GPIO_ACTIVE_LOW>; */
-		/* IRQ gpios = <&pioB 28 GPIO_ACTIVE_LOW>; */
-		status = "okay";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				label = "lan1";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan2";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan3";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan4";
-			};
-
-			port@4 {
-				reg = <4>;
-				label = "lan5";
-			};
-
-			port@5 {
-				reg = <5>;
-				label = "cpu";
-				ethernet = <&macb0>;
-				phy-mode = "rgmii-txid";
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-		};
-	};
-};
-
-&dbgu {
-	status = "okay";
-};
-
-&ebi {
-	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&nand_controller {
-	status = "okay";
-
-	nand@3 {
-		reg = <0x3 0x0 0x2>;
-		atmel,rb = <0>;
-		nand-bus-width = <8>;
-		nand-ecc-mode = "hw";
-		nand-ecc-strength = <4>;
-		nand-ecc-step-size = <512>;
-		nand-on-flash-bbt;
-		label = "atmel_nand";
-	};
-};
-
-&usb0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usba_vbus>;
-	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;	/* PE9, conflicts with A9 */
-	status = "okay";
-};
-
-&pinctrl {
-	board {
-		pinctrl_i2c0_pu: i2c0_pu {
-			atmel,pins =
-				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
-				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
-		};
-
-		pinctrl_mmc0_cd: mmc0_cd {
-			atmel,pins =
-				<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
-		};
-
-		pinctrl_usba_vbus: usba_vbus {
-			atmel,pins =
-				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PE9, conflicts with A9 */
-		};
-
-		pinctrl_spi_ksz: spi-ksz {
-			atmel,pins =
-				<
-				AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PC22 periph A SPI1_MISO pin */
-				AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC23 periph A SPI1_MOSI pin */
-				AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PC24 periph A SPI1_SPCK pin */
-
-				/* SPI CS */
-				AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
-				/* switch IRQ */
-				AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH
-				/* switch PME_N, SoC IN */
-				AT91_PIOC 30 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP
-				/* switch RST */
-				AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH
-				>;
-		};
-	};
-};
diff --git a/configs/platform-v7a_noneon/platformconfig b/configs/platform-v7a_noneon/platformconfig
index 160c422..3ff91ce 100644
--- a/configs/platform-v7a_noneon/platformconfig
+++ b/configs/platform-v7a_noneon/platformconfig
@@ -135,7 +135,7 @@ PTXCONF_KERNEL_IMAGE_Z=y
 PTXCONF_KERNEL_IMAGE="zImage"
 PTXCONF_KERNEL_DTB=y
 PTXCONF_KERNEL_DTS_PATH="${PTXDIST_PLATFORMCONFIGDIR}/dts:${KERNEL_DIR}/arch/${GENERIC_KERNEL_ARCH}/boot/dts"
-PTXCONF_KERNEL_DTS="at91-microchip-ksz9477-evb.dts vexpress-v2p-ca9.dts"
+PTXCONF_KERNEL_DTS="at91-sama5d3_ksz9477_evb.dts vexpress-v2p-ca9.dts"
 # PTXCONF_KERNEL_DTBO is not set
 # PTXCONF_KERNEL_CODE_SIGNING is not set
 # PTXCONF_KERNEL_ZSTD is not set
diff --git a/configs/platform-v7a_noneon/projectroot/loader/entries/sama5d3-ksz9477-evb.conf b/configs/platform-v7a_noneon/projectroot/loader/entries/sama5d3-ksz9477-evb.conf
index bdd9a4b..6ce491d 100644
--- a/configs/platform-v7a_noneon/projectroot/loader/entries/sama5d3-ksz9477-evb.conf
+++ b/configs/platform-v7a_noneon/projectroot/loader/entries/sama5d3-ksz9477-evb.conf
@@ -3,4 +3,4 @@ version		5.8
 options		rootwait rw
 linux-appendroot true
 linux		/boot/zImage
-devicetree	/boot/at91-microchip-ksz9477-evb.dtb
+devicetree	/boot/at91-sama5d3_ksz9477_evb.dtb
-- 
2.39.2